Doorway / InSite Code

Label

Description

Units

Default Value

Range

C1

SACT

Sensor Action
0: Use ’temp’ sensor for control, input 3-4 for high limit/VFC
1: Use average of valid sensor values (INMD = 0)
2: Use maximum of valid sensor values (INMD = 0)
3: Use minimum of valid sensor values (INMD = 0)

-

0

0 to 3

C2

SCAL

Sensor Calibration

Deg C

0

-5 to 5

C3

SPMD

Midpoint of Setpoint Adjustment

Deg C

55

10 to 95

C4

SPRG

Setpoint Adjustment Range

Deg C

25

0 to 50

C5

SPTY

Setpoint Type
0: Setpoint set locally on parameter K1, occupancy supervised from a master Zone Controller using Time Schedule supervision
1: Setpoint (and occupancy) supervised from master Zone Controller using Setpoint Supervision
2: Setpoint set locally on parameter K1, occupancy controlled by multiple zone controllers using Occupancy Demand

-

1

0 to 2

C6

SUMR

Summer Immersion Heater Temperature
Immersion enabled if LOFL allows and Outside temp > SUMR

Deg C

15

0 to 30

C7

LOFL

Low Flow (used with SUMR)
Immersion enabled if SUMR allows and Boiler flow < LOFL

Deg C

30

10 to 70

C8

VMDE

DHW Control Valve Mode
0: DHW Valve closed until boiler flow temp > DHW temp
1: Boiler flow temp ignored
2: DHW heated from VT circuit (set HTSC Heat Source to 0)

-

1

C9

XHRS

Hours Extension when Override set from Dooway / InSite

-

1

0 to 8

C10

FRSE

Fabric/Frost Rise

Deg C

0

0 to 10

C11

INMD

Input Mode for input terminals 3 and 4
0: Additional temperature input for max, min, ave using SACT
1: External occupation (input linked = Occupied) AND
with internal Occupation
2: External occupation (input linked = Occupied) OR
with internal Occupation
3: External Occupation signal only
4: Alarm input
5: Pump Alarm

-

0

0 to 5

C12

MIND

Minimum Demand for occupation output to operate
0: When demand drops to zero, pump continues to run
MIND > 1: When demand drops to zero, pump stops

-

0

0 to 10

C13

OCCO

Occupied Only (select Optimum Start or Occupation Switch operation)
0: Occupancy starts at Optimum Start time
1: Occupancy starts at Occupation Start time

-

0

0 to 1

C14

HPRD

Heating Driver Stroke/Minimum On Time

Secs/10

Depends on driver

1 to 240

C15

HDLY

Heating Interlock Delay

Mins

0

-30 to 30

C16

CPRD

Electric Heating Minimum on Time

Secs/10

Depends on driver

1 to 240

C17

CDLY

Immersion Heater Interlock Delay
Negative value delays pump after immersion heater starts
Positive value runs pump on after immersion heater stops

Mins

0

-30 to 30

C18

FRPT

Frost Protection Mode
0: No action
1: Open DHW valve 50%
2: Open DHW valve and run pump

-

0

0 to 2

C19

MANL

Manual Level, set by Doorway and InSite

%

0

0 to 100

C20

STAT

Thermostatic control mode
0: Normal Fuzzy Logic Control
1: Thermostatic action with +/- 4 Deg C deadband

-

0

0 or 1

C21

AJST

Adjust Start Time. Offsets DHW start from supervising zone

Hrs

0.0

-10 to 10

C22

AJSP

Adjust Stop Time. Offsets DHW stop from supervising zone

Hrs

0.0

-10 to 10

C23

ALRM

Alarm Mode
0: Ignore alarms
1: Report all alarms to Doorway/InSite,
no control action, no flashing Temp indicator
2: Report all alarms, shut down all outputs on alarm
3: Report all alarms, shut down on STOP alarm or local alarm
4: Report all alarms, shut down on STOP alarm only

-

0

0 to 4

C24

ALST

Alarm report sense
0: Alarm if input = 0 (contact open), pump running if input = 1 (closed)
1: Alarm if input = 1 (contact closed), pump running if input = 0 (open)

-

0

0 to 1

C25

HTSC

Heat source

-

1

0 to 8255

C26

OCDS

Occupation Destination

-

0

0 to 8255

C27

HTCT

Heating Demand sent as CT

Deg C

70

0 to 100

Doorway / InSite Code

Label

Description

Units

Default Value

Range

I1 (C30)

FRST

Frost Protection Mode (SPNO violated)

-

-

0 to 1

I2 (C31)

OCC

Occupied

-

-

0 to 1

I3 (C32)

OSRT

Optimum Start in Operation

-

-

0 to 1

I4 (C33)

EXTI

External Input State

-

-

0 to 1

I5 (C34)

HILM

DHW High Limit exceeded

-

-

0 to 1

I6 (C35)

RLYA

Triac A Status

-

-

0 to 1

I7 (C36)

RLYB

Triac B Status

-

-

0 to 1

I8 (C37)

RLYC

Triac C Status

-

-

0 to 1

W1 (C38)

AUTO

Automatic/Manual Status

-

-

0 to 1

W2 (C39)

OVRD

Override

-

-

0 to 1

W5 (C42)

HAND

Manual Hand; use with MANL to set output level

-

0

0 to 1

W6 (C43)

POT

not used in this application

-

0

0 to 1

W7 (C44)

SERV

Service Pin Msg (to Doorway +InSite, self resetting)

-

-

0 to 1

W8 (C45)

CGST

Configuration Mode Status

-

-

0 to 1

S1* (C50)

HWT

Hot Water Temperature

Deg C

-

0 to 95

S2* (C51)

DMND

Control Demand

%

-

0 to 100

S3 (C52)

HWSP

Hot Water Setpoint

Deg C

-

10 to 95

S4 (C53)

HTOP

Heating Output to actuator

%

-

0 to 100

S5 (C54)

OPST

Optimum Start Time

hours

-

0 to 24

S6 (C55)

OPOK

Optimum Start Completion

hours

-

0 to 24

S7 (C56)

HWT2

Hot Water Top Temperature

Deg C

-

0 to 95

K1 (C60)

SPOC

Occupation Setpoint

Deg C

55

10 to 95

K2 (C61)

SPNO

Non-Occupation Setpoint

Deg C

10

5 to 95

K3 (C62)

SPSV

Supervised Setpoint from Master Controller

Deg C

-

0 to 95

K4 (C63)

SPMX

Maximum Temperature high limit

Deg C

0

0 to 95

K5 (C64)

MXOS

Maximum Optimum Start time

hours

6

1 to 24

K6 (C65)

MXOF

Maximum Optimum Stop time

hours

2

0 to 4

Engineering Parameters; only accessible via Doorway and InSite

C90

NOAL

No Alarms; all alarms cleared when set to 1

-

-

0 or 1

C91

SENF

Sensor Failed (when set to 1)

-

-

0 or 1

C92

RPVF

not used in this application

-

-

0 or 1

C93

EXTN

Volt-Free Contact alarm (when set to 1)

-

-

0 or 1

C94

PMPF

Pump Failed (when set to 1)

-

-

0 or 1

C95

STOP

STOP alarm received (when set to 1)

-

-

0 or 1

C160

OPST

Optimum Start time

hours

-

0 to 24

C161

OPOK

Optimum Start Completion

hours

-

0 to 24

C162

MXOS

Maximum Optimum Start time

hours

6

1 to 24

C163

MXOF

Maximum Optimum Stop time

hours

2

0 to 4

C164

OPTE

Optimum start Error allowed

Deg C

1

0.5 to 5

C180

DI A

Input 3-4 digital status

-

-

0 or 1

C181

DI B

Input 5-6 digital status

-

-

0 or 1

* 24 hour plots available for these values by default

Plotting interval and plotted variable changeable via Doorway or InSite